Narrow Gauge Combination Car, builder and date unknown

The origin and build date of #1099 combination car remains a bit of a mystery. The best information available to date suggests that the car was built in Des Moines, IA in the Des Moines & Minneapolis Railroad (DM&M) shop during the winter of 1875-1876. The car is thought to have originally been given the number #7. After only a few years, the car was transferred to the Chicago & Northwestern in August 1879, following the conversion of the DM&M narrow gauge line to standard gauge.
In Southwest Wisconsin between 1872 and 1879, the Galena & Southern Wisconsin Railroad and the Chicago & Tomah Railroad built an extensive 92-mile narrow gauge system between Galena, IL. and Woodman, WI. Both lines had planned to tap the lead mining industry of southwestern Wisconsin while the latter road also intended to carry lumber products from the Tomah area and agricultural products from intermediate points into Chicago.
With both railroads in a state of partial completion and in financial difficulties, the Chicago & North Western Railway (C&NW) purchased them in 1880 and connected them together. In 1882, the C & NW standard gauged all the narrow-gauge line between Fennimore, WI. and Galena, IL. The stretch of track between Fennimore and Woodman, Wisconsin—covering 16.5 miles—remained narrow gauge because it followed the Green River valley, where the valley’s tight confines made modifying the track impractical. It was on this line that the #1099 combine operated. Trains ran daily between Fennimore and Woodman by way of Werley, Anderson Mills and Conely Cut. The line was famous for a horseshoe curve that made it possible to climb the steep slope from the valley to the ridge west of Fennimore. On June 20, 1908, the #1099 was a part of three car train headed to Woodman, WI when the Green River flooded and the water washed away the track and the cars, leaving passengers stranded overnight. Following some minor repairs, car #1099 continued to be used until operations ceased in January 1926, when the C&NW abandoned the line.
The car is of quite simple design and construction, inside dimensions are 29 ft. 10 in. long and 7 ft. 5 in. wide. The car featured an arched roof design that was long obsolete on passenger cars when this car was built. The passenger section is just over 10 ft. long while the baggage is close to twice this length. Each section of the car had a window on each side of the room and the baggage room had a 4 ft. door on each side of the car. With the narrow-gauge body, interior seating ran parallel to the side walls and was covered in rattan. The interior was finished in horizontally laid double-beaded tongue and groove boards up to the roof line with an exposed arched rib ceiling, all woodwork was painted. The car had two stoves in the car and lighting was provided by wall mounted oil lamps. After the turn of the century air brakes (in 1904) and steam heat (1912) were added to the car.
At the time of its abandonment, most of the railroad’s rolling stock was sold off to local farmers and moved to their sites for storage buildings. In the case of the #1099 the trucks and iron were removed from the car and the car body was sold in June 1926 for $25. The car body was relocated to a farm west of Fennimore, Wisconsin, where it served as a small workshop and storage shed.
In 1972 the Mid-Continent Railway Museum acquired the #1099 car body from Loren Welsh’s farm. The car was loaded onto a flatbed trailer and hauled to the MCRM. Since the car sat on the ground from the time of the railroad’s abandonment in 1926 for over 46 years the car body is in poor condition with the framing and woodwork requiring considerable replication for restoration. Regardless, the car is very historically significant and worthy of preservation and restoration. There were only 5 common carrier narrow gauge railroads built in Wisconsin with an aggregate length that never exceeded 200 miles. The C&NW #1099 combination car is one of only two surviving examples of narrow-gauge passenger equipment that operated in Wisconsin and is important to interpret this short-lived and unique era of railroading. The museum is currently in the process of restoring the #1099 to accurately represent what it looked like when it operated on the C&NW Fennimore-Woodman line.


